• 在線留言| 聯系我們| 收藏本站 歡迎光臨無錫雙盛石化裝備有限公司官方網站!
    當前位置:行業新聞

    不銹鋼反應釜的氣密性試驗

    發布日期:2019-09-19 04:41:07 訪問次數:680

    小易為你介紹一下不銹鋼反應釜的氣密性試驗。

    不銹鋼反應釜的過程中,溢流保護裝置在程度上有效地包括氣缸,并且在設定過程中,液體排出口主要位于氣缸的下側,并且在設計過程中 工藝,在缸體上端面的中心位置處的對接接頭,在缸體的上端表面處形成的空氣出口孔,以及用于阻擋彈性墊圈的對接管道正下方的柱狀浮體 對接管的下端口。


     不銹鋼反應釜的靜環端面在程度上可以具有0.05mm的垂直公差。 在操作過程中,該設備可用于液壓試驗,密封處的泄漏量不得超過10ml / h。彈簧不允許有生銹和變形等缺陷,總接觸面積大于80%。不銹鋼反應器機械密封的動環和靜環表面不得有劃痕,凹凸或劃痕,接觸面平整度應符合規定要求。


     不銹鋼反應釜在程度上用作氣密性試驗。在旋轉狀態下,機械密封的油底殼不應產生連續的小氣泡。目視檢查填料密封的填料壓蓋是在末端還是單端。機器密封的油杯中是否有油,雙端機械密封的潤滑系統中的油是否足夠,減速器中的油是否達到油窗的1/3,是否有油 每個潤滑系統漏油。


     在不銹鋼反應釜運行過程中,有效檢查各連接管道上的閥門,管件,絕緣層和管道是否完好無損,操作過程中手動閥門的操作是否有效手輪是否完好,閥門是否關閉,閥門是否平穩打開和關閉,安全閥是否關閉,以及所需的實用程序是否準備就緒。

    英文:

    Xiaoyi will introduce the gas tightness test of stainless steel reactor for you.


    In the process of stainless steel reactor, the overflow protection device effectively includes the cylinder to a certain extent, and in the setting process, the liquid outlet is mainly located at the lower side of the cylinder, and in the design process, the butt joint at the central position of the upper end face of the cylinder block, and the air outlet formed at the upper end surface of the cylinder block. The holes and the lower ports of the cylindrical floating butt pipe directly below the butt pipe for blocking the elastic washer.


    The static ring end face of stainless steel reactor can have a vertical tolerance of 0.05 mm to a certain extent. During operation, the equipment can be used for hydraulic test, and the leakage at the seal can not exceed 10 ml/h. Spring is not allowed to have rust and deformation defects, the total contact area is more than 80%. There shall be no scratches, concave convex or scratches on the surfaces of the moving and static rings of the mechanical seals of stainless steel reactors, and the smoothness of the contact surface shall meet the requirements.


    Stainless steel reactor is used for air tightness test to a certain extent. In the rotating state, the oil pan of mechanical seal should not produce continuous small bubbles. Visually check whether the packing gland of packing seal is at the end or at the single end. Whether there is oil in the oil cup sealed by the machine, whether there is enough oil in the lubrication system of the double-ended mechanical seal, whether the oil in the reducer reaches 1/3 of the oil window, whether there is oil leakage in each lubrication system.


    During the operation of stainless steel reactor, check the valves, fittings, insulating layer and pipelines on the connecting pipes effectively, whether the manual valve is in good condition during operation, whether the valves are closed, whether the valves are opened and closed smoothly, whether the safety valves are closed or not, and the required facts. Is the program ready?

    聯系我們
    服務熱線

    180-1839-6999

    電話號碼0510-85182188

    企業郵箱wxsssh@163.com

    地址無錫市濱湖區胡埭工業園負來橋路10號

    瑞祥祥云